Please be aware that these are “custom” images. They are provided to enable Gen customers to circumvent the block placed by Infomir on Mags which have the latest updates. Once correctly installed you will be able to view content from Gen. You will not be able to edit portals. Appearance of interface will be different from what you are used to, but will work.
I strongly suggest that before you install custom image, that you add two extra portals – these do not need to work or need to be used and can just be copies of existing ones. You will then be able to edit these in future if needed. If you don’t install these “spare” portals there will be no option to edit the working portals in custom image.
If you think you will want to edit portals etc in the future then you need to use older “official” firmware instead.
Mag250 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/58o1EIbT
Mag254 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/poojSQha
Mag256 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/AloBhaSS
Mag322 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/J9pHHajT
Mag324 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/NsoDACoB
Mag349 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/09hBjYRJ
Mag351 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/15ghFYQY
Edit 07/03/2019
The above files can be difficult to remove
If you have installed them to remove:
SSH to the box and remove the custom url hider. Use Putty or terminal)
1. ssh -2 [email protected].*.* (box IP address)
2. 930920 (Password)
3. fw_setenv custom_url_hider=false
4. reboot
5. Then flash firmware found bellow
I recommend using the following images These will preserve portal settings, but disable the block and prevents any remote updates from Infomir’s servers. If you have already used previous custom firmware or installed any other “anti_block settings” then remove all settings to which you have access before trying to install this Better is to install original Infomir software first again by allowing updates and allowing them to complete. This software will fix block later.
Mag250 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/58o1EIbT
Mag254 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/poojSQha
Mag256 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/AloBhaSS
Mag322 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/J9pHHajT
Mag324 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/NsoDACoB
Mag349 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/09hBjYRJ
Mag351 https://mega.nz/folder/g9oHQDYA#t7H9GyX6wArzGNz1DZNTHA/folder/15ghFYQY
Some mag models will not have the Bootstrap included as a separate ‘file’ in that folder. That’s OK, just ensure you transfer the correct folder onto USB device.
MAG254 and earlier can be picky about which sticks they recognize, you may need to try a few – Don’t use USB3.0 sticks. Don’t use sticks larger than 2Gb
To ensure the installation works please install from the recovery area of Mag (hold down menu button during reboot) – Put files on usb (FAT32) in folder named mag*** -(*** is your Magbox number e.g.mag256) – Reset to default first then use usb to downgrade.
End edit
Video guides for updating all MAGs are on Infomir site
Different for each type of box and need to be used with the specific instructions
e.g For 3 series = Guide: https://wiki.infomir.eu/eng/set-top…24-349-351/software-update-mag322-324-349-351. And video can be found half way down page (ctrl +f search for video if you dont see it)
For 2 series except 256https://wiki.infomir.eu/eng/set-top…mag250-254-270/software-update-mag250-254-270Video half way down page
For 256https://wiki.infomir.eu/eng/set-top-box/stb-linux-webkit/mag256/software-update-mag256Video same as 2 series other stuff different
Leave a Reply